„Infra Kulcsok programozása” változatai közötti eltérés
(→Infra Kulcsok programozása) |
|||
| (17 közbenső módosítás, amit 2 másik szerkesztő végzett, nincs mutatva) | |||
| 1. sor: | 1. sor: | ||
== Infra Kulcsok programozása == | == Infra Kulcsok programozása == | ||
| + | [[fájl:InfraKey4.jpg]] | ||
Van még1 módszer | Van még1 módszer | ||
| 13. sor: | 14. sor: | ||
5 Várjál 10 sec-t, míg a programozásból kiszáll, Add rá a gyújtást majd vedd le, várj 20 másodpercet. Kakasáldozat ilyesmik bemutatása következik és közbe a múködj varázsigét mormold | 5 Várjál 10 sec-t, míg a programozásból kiszáll, Add rá a gyújtást majd vedd le, várj 20 másodpercet. Kakasáldozat ilyesmik bemutatása következik és közbe a múködj varázsigét mormold | ||
| + | |||
| + | |||
| + | |||
| + | Jag key programming | ||
| + | |||
| + | I was reading the PATS key and Keyless entry programming entry below and tbh it confused the hell out of me (and the Program a new key is wrong as it shows only needing one programmed key. | ||
| + | |||
| + | Here is a quick (took me 5 mins) guide to programming a jag key (and any remote fob I would assume but don't quote me ;) ) | ||
| + | |||
| + | programming of remote :- ( you will need all your remotes for this ) | ||
| + | |||
| + | insert a programmed key into the ignition. | ||
| + | |||
| + | turn key to position 2 & back four times within 6 second. | ||
| + | |||
| + | when you turn the ignition off after the fourth turn you should hear a beep to tell you your in programming mode for the next 10 seconds. | ||
| + | |||
| + | press any button on your new remote ( a tone will be heard when the car accepts the button press ) now do the same with your old remotes too. | ||
| + | |||
| + | either switch the ignition back on or wait until the timer runs out on the programming mode & your done | ||
| + | |||
| + | Coding key to start the car :- | ||
| + | |||
| + | complete each of the following steps within 5 seconds. | ||
| + | |||
| + | Insert first programmed key in the ignition & turn to position 2 | ||
| + | |||
| + | turn the key back to position 0 & remove from the ignition | ||
| + | |||
| + | Insert second programmed key in the ignition & turn to position 2 | ||
| + | |||
| + | turn back to position 0 & remove the second key, the system is now in programming mode. | ||
| + | |||
| + | now insert you new key & turn to position 2 ( within 10 seconds ) | ||
| + | |||
| + | turn the ignition back to 0 & remove the key & then wait for five seconds. | ||
| + | |||
| + | now try to start the car with your new key, if done ok the car will start, if its failed then the red LED in the clock will flashes after the ignition is switched on. | ||
| + | |||
| + | As I said at the start, it took me 5 mins from start to end and it works nicely now. | ||
| + | |||
| + | You can read on to get confused or be happy here :) | ||
| + | |||
| + | Jag part added by Gingagizmo with help by Compuwiz_uk on 11th March 2007 | ||
| + | |||
| + | |||
| + | [[Kategória:Mk1]] | ||
| + | [[Kategória:Mk2]] | ||
| + | [[Kategória:Minden]] | ||
A lap jelenlegi, 2010. január 1., 21:23-kori változata
Infra Kulcsok programozása
Van még1 módszer
1 Gyújtáskapcsoló I állásába - rádió -, kb 10 sec, az óra mellett lévő piros LED folyamatosan világít
2 Vedd ki a kulcsot mialatt világít, szállj ki, csukd be az ajtót.
3 Tartsd nyomva folyamatosan a nyitó gombot - 1 nyilas - és miután felvillan a kulcson a LED ( 1 sec), a zár gombot - 2 nyilas - nyomd meg háromszor
4 Enged el a nyitó gombot. Tartsd a kulcsot a zár irányába míg az óra melletti LED 5x nem villan, bal lábaddal körözz lassan jobbról balra
5 Várjál 10 sec-t, míg a programozásból kiszáll, Add rá a gyújtást majd vedd le, várj 20 másodpercet. Kakasáldozat ilyesmik bemutatása következik és közbe a múködj varázsigét mormold
Jag key programming
I was reading the PATS key and Keyless entry programming entry below and tbh it confused the hell out of me (and the Program a new key is wrong as it shows only needing one programmed key.
Here is a quick (took me 5 mins) guide to programming a jag key (and any remote fob I would assume but don't quote me ;) )
programming of remote :- ( you will need all your remotes for this )
insert a programmed key into the ignition.
turn key to position 2 & back four times within 6 second.
when you turn the ignition off after the fourth turn you should hear a beep to tell you your in programming mode for the next 10 seconds.
press any button on your new remote ( a tone will be heard when the car accepts the button press ) now do the same with your old remotes too.
either switch the ignition back on or wait until the timer runs out on the programming mode & your done
Coding key to start the car :-
complete each of the following steps within 5 seconds.
Insert first programmed key in the ignition & turn to position 2
turn the key back to position 0 & remove from the ignition
Insert second programmed key in the ignition & turn to position 2
turn back to position 0 & remove the second key, the system is now in programming mode.
now insert you new key & turn to position 2 ( within 10 seconds )
turn the ignition back to 0 & remove the key & then wait for five seconds.
now try to start the car with your new key, if done ok the car will start, if its failed then the red LED in the clock will flashes after the ignition is switched on.
As I said at the start, it took me 5 mins from start to end and it works nicely now.
You can read on to get confused or be happy here :)
Jag part added by Gingagizmo with help by Compuwiz_uk on 11th March 2007
